This is the documentation for etcd2 releases. Read etcd3 doc for etcd3 releases.
etcd can run as a transparent proxy. Doing so allows for easy discovery of etcd within your infrastructure, since it can run on each machine as a local service. In this mode, etcd acts as a reverse proxy and forwards client requests to an active etcd cluster. The etcd proxy does not participate in the consensus replication of the etcd cluster, thus it neither increases the resilience nor decreases the write performance of the etcd cluster.
etcd currently supports two proxy modes:
readonly. The default mode is
readwrite, which forwards both read and write requests to the etcd cluster. A
readonly etcd proxy only forwards read requests to the etcd cluster, and returns
HTTP 501 to all write requests.
The proxy will shuffle the list of cluster members periodically to avoid sending all connections to a single member.
The member list used by an etcd proxy consists of all client URLs advertised in the cluster. These client URLs are specified in each etcd cluster member's
An etcd proxy examines several command-line options to discover its peer URLs. In order of precedence, these options are
initial-cluster option is set to a comma-separated list of one or more etcd peer URLs used temporarily in order to discover the permanent cluster.
After establishing a list of peer URLs in this manner, the proxy retrieves the list of client URLs from the first reachable peer. These client URLs are specified by the
advertise-client-urls option to etcd peers. The proxy then continues to connect to the first reachable etcd cluster member every thirty seconds to refresh the list of client URLs.
While etcd proxies therefore do not need to be given the
advertise-client-urls option, as they retrieve this configuration from the cluster, this implies that
initial-cluster must be set correctly for every proxy, and the
advertise-client-urls option must be set correctly for every non-proxy, first-order cluster peer. Otherwise, requests to any etcd proxy would be forwarded improperly. Take special care not to set the
advertise-client-urls option to URLs that point to the proxy itself, as such a configuration will cause the proxy to enter a loop, forwarding requests to itself until resources are exhausted. To correct either case, stop etcd and restart it with the correct URLs.
To summarize etcd proxy startup and peer discovery:
discoveryis set for the proxy, ask the given discovery service for the peer-urls. The peer-urls will be the combined
initial-advertise-peer-urlsof all first-order, non-proxy cluster members.
discovery-srvis set for the proxy, the peer-urls are discovered from DNS.
initial-clusteris set for the proxy, that will become the value of peer-urls.
advertise-client-urlsof all cluster members (i.e. non-proxies).
Always start the first-order etcd cluster members first, then any proxies. A proxy must be able to reach the cluster members to retrieve its configuration, and will attempt connections somewhat aggressively in the absence of such a channel. Starting the members before any proxy ensures the proxy can discover the client URLs when it later starts.
To start etcd in proxy mode, you need to provide three flags:
To start a readwrite proxy, set
-proxy on; To start a readonly proxy, set
The proxy will be listening on
listen-client-urls and forward requests to the etcd cluster discovered from in
To start a proxy that will connect to a statically defined etcd cluster, specify the
etcd --proxy on \ --listen-client-urls http://127.0.0.1:2379 \ --initial-cluster infra0=http://10.0.1.10:2380,infra1=http://10.0.1.11:2380,infra2=http://10.0.1.12:2380
If you bootstrap an etcd cluster using the discovery service, you can also start the proxy with the same
To start a proxy using the discovery service, specify the
discovery flag. The proxy will wait until the etcd cluster defined at the
discovery url finishes bootstrapping, and then start to forward the requests.
etcd --proxy on \ --listen-client-urls http://127.0.0.1:2379 \ --discovery https://discovery.etcd.io/3e86b59982e49066c5d813af1c2e2579cbf573de \
If you bootstrap an etcd cluster using discovery service with more than the expected number of etcd members, the extra etcd processes will fall back to being
readwrite proxies by default. They will forward the requests to the cluster as described above. For example, if you create a discovery url with
size=5, and start ten etcd processes using that same discovery url, the result will be a cluster with five etcd members and five proxies. Note that this behaviour can be disabled with the
A Proxy is in the part of etcd cluster that does not participate in consensus. A proxy will not promote itself to an etcd member that participates in consensus automatically in any case.
If you want to promote a proxy to an etcd member, there are four steps you need to follow:
We assume you have a one member etcd cluster with one proxy. The cluster information is listed below:
This example walks you through a case that you promote one proxy to an etcd member. The cluster will become a two member cluster after finishing the four steps.
First, use etcdctl to add the member to the cluster, which will output the environment variables need to correctly configure the new member:
$ etcdctl -endpoint http://10.0.1.10:2379 member add infra1 http://10.0.1.11:2380 added member 9bf1b35fc7761a23 to cluster ETCD_NAME="infra1" ETCD_INITIAL_CLUSTER="infra0=http://10.0.1.10:2380,infra1=http://10.0.1.11:2380" ETCD_INITIAL_CLUSTER_STATE=existing
Stop the existing proxy so we can wipe its state on disk and reload it with the new configuration:
ps aux | grep etcd kill %etcd_proxy_pid%
or (if you are running etcd proxy as etcd service under systemd)
sudo systemctl stop etcd
rm -rf %data_dir%/proxy
Finally, start the reconfigured member and make sure it joins the cluster correctly:
$ export ETCD_NAME="infra1" $ export ETCD_INITIAL_CLUSTER="infra0=http://10.0.1.10:2380,infra1=http://10.0.1.11:2380" $ export ETCD_INITIAL_CLUSTER_STATE=existing $ etcd --listen-client-urls http://10.0.1.11:2379 \ --advertise-client-urls http://10.0.1.11:2379 \ --listen-peer-urls http://10.0.1.11:2380 \ --initial-advertise-peer-urls http://10.0.1.11:2380 \ --data-dir %data_dir%
If you are running etcd under systemd, you should modify the service file with correct configuration and restart the service:
sudo systemd restart etcd
If an error occurs, check the add member troubleshooting doc.